hot-rolled sheet & strip, commercial quality (carbon:0.16-0.25 max %) astm a-711 standard spec. for steel forging stock astm a-794 cold-rolled sheet, commercial quality (carbon:0.16-0.25% max) astm a-830 chemical composition requirements for structural quality plates mil-s-11310e steel bars, carbon, hot-rolled, for shaping including cold extrusion
Type 304 is the most widely used alloy of all stainless steels. 300 Series Stainless steel alloys resist corrosion, maintain their strength at high temperatures and are easy to maintain. 300 series grades are inventoried in in stainless steel plate , sheet, bar , pipe, tube and structural products. 304 / 304L - Rolled Alloys, Inc.304 is the original "18-8" stainless. It is produced in greater quantity than any other austenitic stainless steel. 304 provides useful resistance to corrosion in many environments ranging from moderately reducing to moderately oxidizing.
430 stainless steel Type 430 is ductile, has good forming characteristic and is readily fabricated by such operations as bending, pressing, drawing and heading. Its tendency to work harden is much less than that of the nickel-bearing 300 series stainless steel. Cold Finished & Hot Rolled Bar Products - Alro SteelSteel Bars Cold Finished Carbon Bars Cold Finished Bars are produced from Special Bar Quality Hot Rolled Bars by cold drawing, turning or grinding or by a combination of these methods. The cross sectional area of the hot rolled bar is cold reduced, resulting in accurate size, smooth surface, increased mechanical properties and machinability.
CS Type A, Carbon .10% max., allows use of ultra-low carbon CS Type B, Carbon .02% to .15% CS Type C, Carbon .08% max., allows use of ultra-low carbon but also higher phosphorus levels. CS (No Type), Carbon .16% to .25% max. *These specifications replace the former Commercial Quality Grades. Henan BEBON international ,ltd - Steel Plate,Steel 410S stainless steel chemical composition, ASTM A240 410S Stainless steel supplier plate/sheet/coil/ weld and seamless pipe / flat bar / angle . steel / solid round bar / square bar/ hexagonal bar / octagonal steel/ wire The production process of . ASTM A240 410S Stainless steel. we offered are:Hot rolled 410S steel plate, cold rolled
SS400 steel is the most commonly used hot-rolled structural steel (formerly known as SS41) in Japan, and is called general structural rolled steel in JIS G3101. SS400 material is cheap and versatile, and plays an important role in construction, bridges, civil engineering and mechanical equipment structures. Its appearance includes round steel, flat steel (flat steel), steel plates, steel strips and profiles. JIS G3101 SS400 Structural Carbon Steel Plate SpecificationJIS G3101 SS400 is one of the most common carbon structural steel grade, other grades of JIS G3101 are ss330, ss490, ss540. Related product type includes steel plate, steel sheet, steel sections, steel pipes, etc. JIS G3101 Application Range:ss400 steel plate and other steel grades product are applied to general structural constructions-bridges and ships, final product always supplied hot rolled.
General purpose steel bars for machining, suitable for lightly stressed components including studs, bolts, gears and shafts. Often specified where weldability is a requirement. Can be case-hardened to improve wear resistance. Available in bright rounds, squares and flats, and hot rolled rounds. Can be supplied in sawn blanks, and bespoke size SS304 Grade AISI 304 Stainless Steel Properties AISI 304 Grade Stainless Steel (UNS S30400) AISI 304 stainless steel (UNS S30400) is the most commonly used material in stainless steels, and is usually purchased in an annealed or cold worked state. Because SS 304 contains 18% chromium (Cr) and 8% nickel (Ni), its also known as 18/8 stainless steel.Type 304 has good processability, weldability, corrosion resistance, heat resistance, low
- The Chemical Composition of Ss400 SteelsMechanical Properties of Ss400 SteelsComparative MaterialsEquivalent GradesApplications11SMnPb30 / 1.0718 - SteelNumber - Chemical composition Chemical composition % of steel 11SMnPb30 (1.0718):EN 10277-3-2008 Elements not listed in this table shall not be intentionally added to the steel without the agreement of the purchaser, other than for the purpose of the finishing the heat.
Stainless Steel - General Information - EN Standards for EN Standards for Stainless Steel Bar. The old BS970 Parts 1 & 3:1991 standards have been replaced by a number of EN Standards, the most important of which are shown below EN10088-3 Replaces BS970 Part 1:1991 & BS970 Part 3:1991 covering chemical composition & mechanical properties EN10058 Tolerances for Hot Rolled Flat Bars
Grade Summary:Excellent mechanical properties, resistance to many corrosive agents. Useful where sanitation and cleanliness are important. Non magnetic in the annealed condition. Hardness and tensile strength can be increased by cold working, but modified by lowered carbon content providing good resistance to corrosion in welded construction where subsequent heat treatment is not practical. Stainless Steel 304L - 1.4307 Data SheetStainless steel 304 and 304L are also known as stainless steel 1.4301 and 1.307 respectively. Type 304 is the most versatile and widely used stainless steel. It is still sometimes referred to by its old name 18/8 which is derived from the nominal composition of type 304 being 18% chromium and 8% nickel.
Stainless steel 430 - 1.4016 is a very popular and versatile grade of stainless steel. Is it used in a variety of industries due to its combination of strength and corrosion resistance versus cost. We at thyssenkrupp Materials (UK) supply 430 in a variety of forms off the shelf for next day delivery or, available as bespoke sizes on a call off basis. Stainless Steel Bar Round, Flat, Angle and SectionsCommon Stainless Steel Bar Specifications ASTM A276M Hot or cold finished bar except bars for reforging (see ASTM A314). Includes rounds, squares, hexagons, hot rolled or extruded shapes such as angles, flats, channels and commonly used grades of stainless steel, including improved machinability.
Properties A 663/A 663M Steel Bars, Carbon, Hot-Wrought, Special Quality, Me-chanical Properties A 675/A 675M Steel Bars for Springs, Carbon and Alloy A 689 Cold-Finished Carbon Steel Bars:Steel Bars, Carbon and Alloy, Cold-Finished A 108 Cold-Drawn Stress-Relieved Carbon Steel Bars Sub-ject to Mechanical Property Requirements A 311/A 311M Hot Structural Steel:JIS G3101, SS400, ASTM A36, ASTM A283 JIS G 3101 SS400 is one of the most commonly used hot rolled general structural steel. Supplied as plates, sheets, flats, bars, sections etc. They are cheap, excelling in weldability and machinability.
during forming. AK Steel can directly affect the mechanical properties of the steel. Tight control over chemical composition, hot rolling parameters, amount of cold reduction, annealing time and temperature, and the amount of temper rolling allow the production of high-quality Cold Rolled Steel products to meet customer requirements.